|
|
| |
| 木材防腐設備 |
| 產品類別：干燥設備 瀏覽數量：6450 |
|
|
產品描述：
木材防腐設備涵蓋了木材防腐，木材阻燃，木材染色的全部功能，設備按照國際通行標準設計，可同時分別按照滿細胞法 ，高低頻壓法，雙真空法等。設備工作壓力是-0.08M怕-3.6MPA，工作溫度是0-200度，相對真空度0.098M怕，一次可防腐木材從2M3 到20M3不等。
木材防腐設備維護事項
Wood preservation equipment maintenance
1. To daub regula butter in the turbine ,screw ,bearing which are tank opening device at the fixed time,,keep oil state
1、罐門開啟裝置的渦輪及絲桿、軸承要定期涂抹黃油，保持有油狀態
2.To keep clean of the tank sealing ring ,the contact surface,before shut the door ,so should be with mechanical lubricating oil on seal ring and cans incisors surface ,keep sealing and cans door switch freely
2、罐門密封圈表面及與之接觸面要保持清潔，關罐門前要用毛刷沾機械潤滑油涂刷密封圈及罐門齒表面，保持密封性及罐門開關自如。
3.To daub mechanical lubrication oil on the valves and screw in order to avoid jamming pipeline and pump body.
3、各閥門絲桿要定期涂刷機械潤滑油，以免其堵塞管道及泵體。
4.To clean bits of wood or any other impurities inside stainless steel filter and pressure tank.
4、要定期清除不銹鋼過濾器及壓力罐內木屑等雜質，以免其堵塞管道及泵體。
5.To keep water in vacuum pump cooling water tank ,it is strictly prohibited to open pump without water,and to clean water tank,keep the water clean inside of water tank.
5、真空泵冷卻水箱內要保持有水狀態，嚴禁無水開泵，且要定期清洗水箱，保持水箱內水質清潔。
6.Before opening pressure pump,need to confirm if the valve is open between liquid storing box and pressure pump (liquid storing have enough potions).it is strictly prohibited to open pump without liquid.
6、加壓泵開泵前要確認與儲液箱間閥門開啟（且儲液箱內有足夠藥劑），嚴禁無液開泵運轉。
7.To inspect the relief every year and inspect pressure gauge every six months
7、安全閥每一年、壓力表每半年校驗一次。
。
常見故障和排除方法
Common faults and elimination methods
故障現象
Fault phenomenon
可能原因
Possible cause
排除方法
升壓緩慢或不升壓
Boost slowly or not boost
1、加壓泵前的過濾器（或底閥）濾網堵塞。
Filter (or bottom valve )is at the front of pressure pump which is blocked
2、木材裝載過高，堵住了罐頂加壓管口。
Loaded wood is too high ,block pressure pipe mouth
3、加壓管路堵塞。
Pressure pipe is blocked
1、拆洗過濾器（或底閥）濾網。
Uppick and wash the mesh of the filter (or bottom valve)
2、降低木材裝車高度，使木材頂端距離罐頂留有10公分間隙并將木材用強繩扎緊。
Reduce the load wood height ,assure at least 10cm gap between the top of wood and tank deck
3、管路清淤。
Clean the pipe
罐門關閉后開始作業時，真空泵不能啟動
After closed the door ,the vacuum pump cann't start
罐門開啟裝上的下行程開未能閉合，從而未能給控制柜罐門已關閉信號。
The door of open device downstroke failed to close ,cann't give control cabinet a closed signal
調整觸點使下行程開關閉和。
Adjust the contact to close the downstroke
作業結束后罐門不能開啟
After manufacture ,the door cann't be opened
電接點壓力表的工作指針歸零后未能與下限位指針接觸。
The contact pressure gauge pointer to zero which don't contact the lowest limit pointer
壓力表為零時，將下限位指針稍上調，調至與工作指針接觸即可。
When the pressure gauge is zero ,adjust lowest limit pointer a little to make working pointer contact |
|
|
| |
|
|
|
